Pass Authentic Cisco 300-510 with Free Practice Tests and Exam Dumps
New 300-510 Exam Questions Real Cisco Dumps
Prerequisites for Final Exam
The individuals concerned will already have awareness and skills involving how to execute and operate Cisco core technologies for the networks that are targeted at the Service Providers. They should also have a deep comprehension of the 300-510 subject matter so gaining the requisite knowledge takes deliberate learning that makes use of recommended courses as well as revision or study guides. Potential candidates should also be aware of the registration process for the official test. Thus, they should have a Pearson VUE account before they can do the final registration, which includes selecting the number of the evaluation they intend to do.
NEW QUESTION # 78
An engineer warns to map a multicast IP address to a multicast MAC.
How many bits are used to make the conversion?
- A. high-order 24 bits
- B. low order 23 bits
- C. lower-order 24 bits
- D. higher-order 23 bits
Answer: B
NEW QUESTION # 79
Refer to the exhibit.
Refer to the exhibit. Mid-sized company Z connected two branch offices via a multicast-enabled ISP using the BGP routing protocol. PIM was implemented to support multicast streaming between the branches via MSDP Client A cannot connect to the multicast stream source of company Z. The network engineer ran a debug on the edge of the network as shown. Which action resolves the issue?
- A. Enable the BGP routing protocol and advertise the 10 10.10.0/24 subnet on R1.
- B. Configure the PIM protocol on the Serial 1/1 interface and enable Auto-RP
- C. Deploy BSR on routers R1 and R2 and enable multicast on both LAN segments.
- D. Implement MBGP and enable a multicast address family on R2
Answer: C
NEW QUESTION # 80 
Refer to the exhibit. A network engineer is configuring router R3 to handle multicast streams, but Host-2 cannot send subscriptions messages to the IPTV source. Which configuration must the engineer apply to router R3 so it passes the IPTV stream to Host-2?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION # 81
What is the characteristic of enabling segment routing for IGPs?
- A. Segment routing must first be enabled globally and then under the routing process.
- B. Segment routing must be enabled only globally.
- C. Segment routing must first be enabled under the routing process and then globally.
- D. Segment routing must be enabled only under the routing process.
Answer: A
NEW QUESTION # 82
Refer to the exhibit.
A service provider is running IS-IS in the core, and all routers use the default IS-IS configuration and reside in the same area. All routers maintain a different 6 bytes for the system ID. but the attached bits in the NET are the same. After an engineer added router R6 to the network. R3 and R5 began to experience CPU processing issues. Which action must the engineer take to resolve the issue?
- A. Configure routers R5 and R3 to operate as Level 1 routers only so that they inject a default routing into the routing tables of the other routers
- B. Configure all routers to operate as IS-IS Level 2 routers so that only a Level 2 database is maintained.
- C. Configure R6 to operate as a Level 1 router only so that it maintains the Level 1 database for all routers.
- D. Configure all routers lo operate as IS-IS Level 1 routers by altering the attached bit to ensure that a default route is Injected Into the routing tables.
Answer: B
NEW QUESTION # 83
Refer to the exhibit.
Refer to the exhibit. Users at the branch office on R1 reported issue with an application at the home office on R4. While troubleshooting the issue, a network engineer determined that The branch-office users can connect to the home office.
The IS-IS adjacencies between R1 and R2 and R1 and the branch office are up.
Traffic from R1 to the R2 10.20.1.0/24 network is moving normally.
The application at the home office is experiencing packet drops on the connection to the Branch, and R3 cannot reach the R1 172.16.10.0/24 network.
Which action resolves the issues?
- A. Configure the IS-IS core instance on the RI GigabitEthernet0/3 interface.
- B. Configure the IS-IS core instance on the R2 GigabitEthernet0/1 interface.
- C. Redistribute static connected routes in IS-IS on router R4.
- D. Redistribute static connected routes in IS-IS on router RI.
Answer: A
NEW QUESTION # 84
Refer to the exhibit. Which task must you perform on interface g1/0/0 to complete the SSM implementation?
- A. enable CDP
- B. disable IGMP
- C. configure IGMPv3
- D. configure OSPFv3
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_pim/configuration/xe-16/imc-pim-xe-16- book/imc-ssm.html
NEW QUESTION # 85
Refer to the exhibit. Router 1 resides in a different data center than Router 2 and Router 3.
Router 1 is running the IS-IS routing protocol, and it is preconfigured with LDP and segment routing. Which configuration must the engineer apply under router isis 111 on Router 1 to implement TI-LFA on the link to Router 2 without disrupting traffic to Router 3?
- A. interface GigabitEthernet0/0/1
fast-reroute per-prefix ti-lfa enable - B. interface GigabitEthernet0/0/1
fast-reroute prefix enable - C. interface GigabitEthernet0/0/1
address-family ipv4 unicast
fast-reroute per-prefix
fast-reroute per-prefix ti-lfa - D. interface GigabitEthernet0/0/1
address-family ipv4 unicast
fast-reroute per-prefix
Answer: C
NEW QUESTION # 86
Refer to the exhibit.
After troubleshooting BGP traffic steering issue, which action did the network operator take to achieve the correct effect of this configuration?
- A. Routes directly attached to AS 65517 have the local preference set to 150.
- B. Routes that have passed through AS 65517 have the local preference set to 150.
- C. Routes that have passed through AS 65517 have the local preference set to 150 and the traffic is denied.
- D. Routes that have originated through AS 65517 have the local preference set to 150.
Answer: B
NEW QUESTION # 87
Refer to the exhibit.
Refer to the exhibit. HostB receives an IPTV traffic stream from the multicast source at 192.168 10.1. When router RB is powered down, it impacts multicast traffic forwarding to downstream peers. The RA and RB routers reside in the same physical location. Which two configurations must be implemented so that HostB receives the multicast stream even when RB is powered down? (Choose two )
- A. Set the backup RP address to 10 10 10.3 on routers RY and RZ.
- B. Set the RP address to 10.10.10.4 on all routers
- C. Enable PIM SSM mode on routers RA and RY.
- D. Enable bi-directional PIM on all routers.
- E. Enable PIM sparse mode on routers RC and RZ with a static RP address of 10.10.10.1.
Answer: C,E
NEW QUESTION # 88
Refer to the exhibit.
A network engineer applied configuration on R5 to summarize all OSPF routes, but R4 is still receiving specific routes from R5. The engineer has confirmed that both R5 and R4 routers are configured with correct summarization configuration but R5 Is not sending the summary routes What action must the engineer take to fix the problem?
- A. Remove summarization configuration on R5 and configure it on R4
- B. Configure a sham link between R4 and R5 to support summarization within Area 2
- C. Clear link-state database on both R4 and R5 routers for summarization to work
- D. Move R4 and R5 in separate areas as now they maintain the same link-state database
Answer: D
NEW QUESTION # 89
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. weight
- B. local preference
- C. MED
- D. origin
Answer: B
Explanation:
Weight is local to the router while LP allows routers in an AS with multiple exit points to choose which exit point is used to reach a particular NLRI.
NEW QUESTION # 90
Refer to the exhibit.
Refer to the exhibit Networks 172.16.31.0/24 and 172 16 30.0/24 are advertised in area 34. and network 172.22 10.0/24 is advertised in area 0. A recent security review discovered that users connected to routers R1 and R2 have been making unauthorized access to an application running on network 172 16 31 0/24 An engineer determined that routers R1 and R2 are receiving updates for network 17 16 31 0/24 Which action resolves the issue?
- A. Apply route filtering on router R3 only.
- B. Apply route filtering on routers RI and R2
- C. Apply route filtering on routers R3 and R4.
- D. Apply route filtering on router R4 only.
Answer: D
NEW QUESTION # 91
Which statement about BFD on Cisco IOS XR Software is true?
- A. BFD is not compatible between Cisco IOS XR and Cisco IOS Software.
- B. Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.
- C. Cisco IOS XR Software does not support BFD multihop for IPv4.
- D. Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-3/routing/configuration/ guide/b-routing-cg-asr9000-63x/b-routing-cg-asr9000-63x_chapter_0100.html
NEW QUESTION # 92
Refer to the exhibits.
A network operator is troubleshooting packet loss seen from the R1 loopback interface to the R2 loopback interface over the core network. The operator is attempting to identify the next leg in the path from PE1.
Which interface and label path should the operator investigate next?
- A. PE1 - Gi0/0/0/3 - forwarding label 24002
- B. PE1 - Gi0/0/0/2 - forwarding label 24002
- C. PE1 - Gi0/0/0/2 - forwarding label 24001
- D. PE1 - Gi0/0/0/3 - forwarding label 24001
Answer: D
NEW QUESTION # 93
......
Cisco 300-510 certification exam is an excellent opportunity for professionals looking to enhance their skills and knowledge in the field of service provider routing solutions. Implementing Cisco Service Provider Advanced Routing Solutions certification validates a candidate's ability to implement advanced routing technologies and solutions in a service provider environment. To succeed in the exam, candidates must have a good understanding of the different service provider network architectures and technologies, as well as the ability to configure, troubleshoot, and manage advanced routing technologies.
Cisco 300-510 (Implementing Cisco Service Provider Advanced Routing Solutions) certification exam is an excellent opportunity for candidates who want to demonstrate their expertise in service provider routing solutions. By passing this certification exam, candidates can improve their career prospects in the field of network engineering and become an integral part of their organization's service provider routing solutions team.
300-510 Exam Info and Free Practice Test Professional Quiz Study Materials: https://freetorrent.braindumpsvce.com/300-510_exam-dumps-torrent.html